| Samsung Odyssey, ViewFinity, Smart Monitor (US) | No US policy published | | | |
- Lines covered
- US policy (Odyssey, ViewFinity, Smart Monitor)
- Notes
- No published US (or UK) Samsung monitor pixel policy found. Searched samsung.com/us and samsung.com/uk for dead pixel / bright dot / ISO 9241-307 policy pages and for Odyssey OLED zero-bright-pixel claims; only Samsung community forum threads (not policy) and third-party guides turned up.
Source: Samsung US Support, read 2026-11-16 |
| Dell UltraSharp | 0 (any bright pixel or bright subpixel qualifies)Counted in sub-pixels | Up to 5 dark subpixels; up to 5 total combined defects | Yes, bright only | 1 year or 3 years ('Most Dell monitors come with a 1-year or 3-year limited warranty'; not specified per line) |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels (typically less than half a subpixel; not distinguishable from a subpixel without magnification) are not classed as defects. Only stuck pixels/subpixels visible at normal viewing distance (about 35 to 50 cm; 100 to 150 cm for large format) count. No cluster or zone rule stated.
- Zero defect terms
- Bright pixels and bright subpixels only (up to 5 dark subpixels still allowed). Lasts the entire warranty period: standard (1 or 3 years) plus any purchased extended warranty.
- Lines covered
- UltraSharp (U series and UltraSharp PremierColor UP series) - Premium Panel Exchange
- Notes
- Dell's name is 'Premium Panel Exchange'. Article last modified 12 Oct 2026 (version 46). Table columns: 'Bright Pixels/Subpixels Allowed' / 'Dark Subpixels Allowed' / 'Total Combined Defects Allowed'; the dark limit is counted in subpixels, while the bright column counts a whole bright pixel or a single bright subpixel each as one defect. The same PPE terms apply to Dell Pro P series (bullet list excludes P1424H and P1425) and C/P-series conferencing monitors 24-34 in. No ISO class cited ('industry-standard guidelines'). US Best Buy purchases can be exchanged at any Best Buy store with the original receipt.
- From the policy
- “This guarantee means zero tolerance for bright pixels on eligible displays. If you see even one bright pixel during your warranty period, we'll replace your display.”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| Dell S series (2020+) and G series | 0 (any bright pixel or subpixel qualifies)Counted in sub-pixels | Up to 5 dark subpixels; up to 5 total combined defects | Yes, bright only | 1 year or 3 years (Dell states the standard warranty is 1 or 3 years; not specified per line on this page) |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels are not classed as defects. No cluster or zone rule stated.
- Zero defect terms
- Bright pixels/subpixels only, for the entire warranty period including any extended warranty. S series covered only for 2020 and newer models; S2716DG and S2417DG excluded.
- Lines covered
- Dell S series (2020 and newer) and G series / S-series gaming monitors - Premium Panel Exchange
- Notes
- Excluded S2716DG and S2417DG fall under the standard table: up to 5 bright, up to 5 dark, up to 5 total. Pre-2020 S series models are not listed as covered.
- From the policy
- “Dell S monitors (S series, 2020 and newer models). Gaming monitors (G series and most S series gaming monitors, except S2716DG and S2417DG).”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| Dell SE series | Up to 5 bright pixels/subpixelsCounted in sub-pixels | Up to 5 dark subpixels; up to 5 total combined defects | No | 1 year or 3 years (Dell states the standard warranty is 1 or 3 years; not specified per line on this page) |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels are not classed as defects. No cluster or zone rule stated.
- Lines covered
- Dell SE series (standard, no Premium Panel Exchange)
- Notes
- Same standard limits listed for IN series and Dell Pro E series (5 bright / 5 dark / 5 total). D series: 5 bright / 8 dark / 8 total. C-series large format 43 in and up: 5 bright / 12-15 dark / 12-15 total. The FAQ restates: without Premium Panel Exchange, a bright dot is covered 'Only if you have more than 5 total stuck pixels/subpixels'. The bright limit counts whole pixels and single subpixels alike.
- From the policy
- “Dell (SE series) | Up to 5 | Up to 5 | Up to 5 (standard monitors table: Bright Pixels/Subpixels Allowed, Dark Subpixels Allowed, Total Combined Defects Allowed).”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| Dell Alienware | 0 (any bright pixel or subpixel qualifies)Counted in sub-pixels | Up to 5 dark subpixels; up to 5 total combined defects | Yes, bright only | 1 year or 3 years per Dell pixel guidelines; QD-OLED models: 'limited to a 3-year maximum warranty term, includes burn-in' |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels are not classed as defects. No cluster or zone rule stated.
- Zero defect terms
- Bright pixels/subpixels only, for the entire warranty period including any extended warranty.
- Lines covered
- Alienware (all AW monitors except AW5520QF, AW3926QW, AW2726DL, AW2526HL) - Premium Panel Exchange
- Notes
- No separate Alienware-branded pixel policy exists; Alienware is covered by Dell's article. The Alienware Monitor Support Services page (https://www.dell.com/support/contents/en-us/article/warranty/alienware-monitor-support-services) says 'Dell Premium Panel Exchange allows a free panel replacement during the Dell Limited Hardware Warranty period even if only one bright pixel is found' and 'QD-OLED panel technology is limited to a 3-year maximum warranty term, includes burn-in.' Advanced Exchange: replacement 'often within one to two business days'. The PPE eligibility bullet list says 'Alienware monitors (AW series, except AW5520QF)', which does not exclude AW3926QW, AW2726DL or AW2526HL, while the tables put those three in other rows.
- From the policy
- “Alienware (all models except, AW5520QF, AW3926QW, AW2726DL, and AW2526HL) | 0 | Up to 5 | Up to 5”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| Dell Alienware AW5520QF and AW3926QW | 0 (any bright pixel or subpixel qualifies) per the PPE table; AW5520QF eligibility contradicted by the bullet listCounted in sub-pixels | Up to 12 dark subpixels; up to 12 total combined defects | Yes, bright only | 1 year or 3 years per Dell pixel guidelines |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels are not classed as defects. No cluster or zone rule stated.
- Zero defect terms
- Bright pixels/subpixels only, for the entire warranty period, per the 'Monitors with Premium Panel Exchange' table. Clear for AW3926QW; for AW5520QF the same page's eligibility list excludes it, so AW5520QF's zero-bright coverage is contradictory.
- Lines covered
- Alienware AW5520QF and AW3926QW
- Notes
- Internal contradiction on Dell's page (v46, 12 Oct 2026). (1) 'Which Displays Are Covered?' bullet list: 'Alienware monitors (AW series, except AW5520QF)' - i.e. AW5520QF is NOT PPE-eligible, AW3926QW is. (2) The 'Monitors with Premium Panel Exchange' table lists 'Alienware AW5520QF and AW3926QW | 0 | Up to 12 | Up to 12' - i.e. AW5520QF IS PPE with 0 bright allowed. (3) The first Alienware PPE table row excludes 'AW5520QF, AW3926QW, AW2726DL, and AW2526HL', and the standard (non-PPE) table does not list AW5520QF at all. Treat AW5520QF bright-pixel coverage as unresolved; AW3926QW is consistent across both parts.
- From the policy
- “Alienware AW5520QF and AW3926QW | 0 | Up to 12 | Up to 12”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| Dell Alienware AW2526HL and AW2726DL | Up to 2 bright pixels/subpixelsCounted in sub-pixels | Up to 5 dark subpixels; up to 5 total combined defects | No | 1 year or 3 years per Dell pixel guidelines |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Partial subpixels are not classed as defects. No cluster or zone rule stated.
- Lines covered
- Alienware AW2526HL and AW2726DL (standard, no Premium Panel Exchange)
- Notes
- Listed in Dell's 'Standard Monitors without Premium Panel Exchange' table. The PPE eligibility bullet list ('Alienware monitors (AW series, except AW5520QF)') does not exclude these two models, so the page is inconsistent about them too; the table is the more specific statement.
- From the policy
- “Alienware AW2526HL and AW2726DL | Up to 2 | Up to 5 | Up to 5”
Source: Dell Display Pixel Guidelines | Dell US (Article 000126004), read 2026-11-16 |
| LG All monitors (US help page) | Advice only, not warranty terms: 'if there are bright spots' on a black background: 'ask for help at the seller' (not stated as a warranty threshold; does not say whether a single spot is enough) | '6 or more dark spots including all red/green/blue colors': 'ask for help at the seller' (not stated as a warranty threshold) | Not stated | Not stated |
- Counted in
- dot (not defined)
- Lines covered
- All monitors (US troubleshooting guidance)
- Notes
- Troubleshooting article, not a warranty policy; it directs buyers to the seller rather than promising LG replacement, and contains no wording about warranty, dead pixels or technicians. Do not treat as a zero-bright-pixel guarantee. _n values left null because these are not replacement thresholds.
- From the policy
- “After displaying the screen in black background, if there are bright spots then ask for help at the seller. If there are 6 or more dark spots including all red/green/blue colors, then ask for help at the seller.”
Source: LG Monitor - Troubleshooting the Monitor Screen | LG USA Support, read 2026-11-16 |
| LG OLED monitors incl. UltraGear OLED | No US policy published | | | 2 years parts/labor, including OLED display panel |
- Lines covered
- UltraGear OLED / LG OLED monitors
- Notes
- No pixel-defect thresholds in the warranty card and no OLED-specific LG pixel policy found. The card excludes 'Minor imperfections that do not materially alter or affect functionality.' The LCD pixel policy PDF covers LCD monitors only.
- From the policy
- “PARTS/LABOR: 2 Years from the date of original retail purchase, or from the date of delivery as per applicable law (internal and functional parts only, including OLED Display Panel)”
Source: Limited Warranty - USA ONLY, OLED MONITOR (Warranty Card Monitor_Gaming_OLED, MBM67504230 REV02), read 2026-11-16 |
| Asus ROG Swift PG series (non-OLED) | 0 in months 1-12 after purchase; up to 3 tolerated in months 13-36Counted in sub-pixels | up to 5 tolerated (36 months) | Yes, bright only | 36 months |
- Counted in
- sub-pixel
- ISO class cited
- ISO 9241-302 (as cited by ASUS; no class stated)
- Sub-pixel or cluster rule
- Counts are per sub-pixel (bright dot = sub-pixel always on under black pattern; dark dot = sub-pixel always off under any pattern). Micro Dot, less than or equal to 1/2 dot, is excluded. No cluster/adjacency/zone rule stated.
- Zero defect terms
- Zero Bright Dot: 0 bright dots allowed for the first 12 months after purchase on PG Series (non-OLED); bright dots only, dark dots excluded from ZBD. Months 13-36 revert to up to 3 bright.
- Lines covered
- ROG Swift PG Series (Zero Bright Dot; non-OLED)
- Notes
- Same generic text appears on every US model warranty page checked (PG38UQ, PA278CGV, VG27AQ1A, PG27UCDM, XG27AQDMG, VA27EHF). ZBD table applies to "PG Series (OLED Models not applicable)". The page does not name ROG Strix or TUF; placing other ROG lines (e.g. Strix XG) under Non-ZBD is an inference from model naming. OLED PG models on the 24-month OLED footnote list are excluded from this table. ASUS ZBD article (asus.com/us/support/Article/696) says "ASUS may repair or replace the unit" and "Exclusions apply and subject to verification." Page notes "Non-ZBD/ZBD warranty models may vary from different regions." bright_allowed_n reflects the 12-month ZBD period; months 13-36 tolerate up to 3. Australia/NZ terms differ (see AU row).
- From the policy
- “Covered Models: PG Series (OLED Models not applicable) | After Purchase 12 months: Bright Dot 0, Dark Dot ≦5 | 13~36 months: Bright Dot ≦3, Dark Dot ≦5.”
Source: ASUS US monitor Warranty page (HelpDesk_Warranty): LCD Panel Bright/Dark Dot Warranty & Regulation, read 2026-11-16 |
| Asus ProArt PA series (non-OLED) | 0 (any bright dot qualifies) for 36 monthsCounted in sub-pixels | up to 5 tolerated | Yes, bright only | 36 months |
- Counted in
- sub-pixel
- ISO class cited
- ISO 9241-302 (as cited by ASUS; no class stated)
- Sub-pixel or cluster rule
- Counts are per sub-pixel (bright dot = sub-pixel always on under black pattern; dark dot = sub-pixel always off under any pattern). Micro Dot, less than or equal to 1/2 dot, is excluded. No cluster/adjacency/zone rule stated.
- Zero defect terms
- 0 bright dots for the full 36 months on PA Series (non-OLED); bright only, dark dots up to 5 tolerated.
- Lines covered
- ProArt PA Series (non-OLED)
- Notes
- OLED ProArt models PA27DCE, PA27DCE-K, PA32DC are on the separate 24-month OLED list (≦3 bright, ≦5 dark). Other ProArt-branded models without a PA model name (e.g. PQ22UC) are not covered by this row. Policy text cites 'ISO 9241-302' and says 'ASUS conforms to the acceptance level between 3 to 5 defective bright/dark pixels'.
- From the policy
- “Covered Models: PA Series (OLED Models not applicable) | After Purchase 36 months: Bright Dot 0, Dark Dot ≦5.”
Source: ASUS US monitor Warranty page (HelpDesk_Warranty): LCD Panel Bright/Dark Dot Warranty & Regulation, read 2026-11-16 |
| Asus Listed OLED models (ROG and ProArt) | up to 3 toleratedCounted in sub-pixels | up to 5 tolerated | No | 24 months |
- Counted in
- sub-pixel
- ISO class cited
- ISO 9241-302 (as cited by ASUS; no class stated)
- Sub-pixel or cluster rule
- Counts are per sub-pixel (bright dot = sub-pixel always on under black pattern; dark dot = sub-pixel always off under any pattern). Micro Dot, less than or equal to 1/2 dot, is excluded. No cluster/adjacency/zone rule stated.
- Lines covered
- Listed OLED models (PQ22UC, MQ13AH, MQ16AH, PA27DCE, PA27DCE-K, PA32DC, PG27AQDM, PG34WCDM, PG42UQ, PG48UQ, PG49WCD)
- Notes
- Page footnote: "*OLED Models: PQ22UC, MQ13AH, MQ16AH, PA27DCE, PA27DCE-K, PA32DC, PG27AQDM, PG34WCDM, PG42UQ, PG48UQ, PG49WCD apply 24 months warranty." Includes ROG and ProArt OLED models that are excluded from the ZBD/PA tables. Page: "For other OLED models not listed, they all apply 36 months warranty" - those unlisted OLEDs appear to fall under the Non-ZBD table, but the page does not say so explicitly.
- From the policy
- “Covered Models: PQ22UC, MQ13AH, MQ16AH, PA27DCE, PA27DCE-K, PA32DC, PG27AQDM, PG34WCDM, PG42UQ, PG48UQ, PG49WCD | After Purchase 24 months: Bright Dot ≦3, Dark Dot ≦5.”
Source: ASUS US monitor Warranty page (HelpDesk_Warranty): LCD Panel Bright/Dark Dot Warranty & Regulation, read 2026-11-16 |
| Asus All other models (incl. TUF and ROG Strix) | up to 3 toleratedCounted in sub-pixels | up to 5 tolerated | No | 36 months |
- Counted in
- sub-pixel
- ISO class cited
- ISO 9241-302 (as cited by ASUS; no class stated)
- Sub-pixel or cluster rule
- Counts are per sub-pixel (bright dot = sub-pixel always on under black pattern; dark dot = sub-pixel always off under any pattern). Micro Dot, less than or equal to 1/2 dot, is excluded. No cluster/adjacency/zone rule stated.
- Lines covered
- Others (Non-ZBD Models); TUF Gaming, ROG Strix and other non-PG/PA and unlisted OLED models placed here by inference (not named by ASUS)
- Notes
- The page does not name TUF or ROG Strix anywhere (TUF appears only in site navigation); they are placed here only because they are not PG/PA series and not on the OLED list - an inference from model naming, not stated by ASUS. Unlisted OLED models get 36 months per the page, but the page does not explicitly assign them to this table. Adaptor and built-in battery have 12 months warranty.
- From the policy
- “Covered Models: Others (Non-ZBD Models) | After Purchase 36 months: Bright Dot ≦3, Dark Dot ≦5.”
Source: ASUS US monitor Warranty page (HelpDesk_Warranty): LCD Panel Bright/Dark Dot Warranty & Regulation, read 2026-11-16 |
| AOC Standard | 1 full bright ("stuck on white") pixel tolerated, alongside Class 1 sub-pixel allowances; exceeding these qualifiesCounted in pixels and sub-pixels | 1 full dark ("stuck off") pixel tolerated, alongside Class 1 sub-pixel allowances; exceeding these qualifies | No | 3 years, except 1 year for LED panel (General Warranty Statement); 3 years for G-Series under Re-Spawned Limited Warranty |
- Counted in
- mixed
- ISO class cited
- ISO 9241-307 Class I
- Sub-pixel or cluster rule
- Also tolerated: '2 single or double bright or dark sub-pixels' and '3 to 5 stuck on or stuck off sub-pixels (depending on the number of each)'. No distance/zone rule stated.
- Lines covered
- Standard (all AOC LCD/LED monitors, incl. G-Series)
- Notes
- US/Canada terms ("For AOC LCD/LED monitor sold in United States and Canada") from TPV USA Corp / Envision Peripherals (EPI). The page itself states the numbers (1 full bright pixel, 1 full dark pixel, 2 single or double bright or dark sub-pixels, 3 to 5 stuck on/off sub-pixels). The general statement covers the LED panel for only 1 year. A 90-day EASE Replacement Program uses the same Class 1 thresholds. Separate "Re-Spawned Limited Warranty" covers G-Series (3 years) with Defect defined as pixel defect exceeding ISO 9241-307 Class 1, and EPI replaces with a new monitor; excludes purchases before Jan 1, 2019; purchases from EPI or authorized distributors/resellers in the US or Canada. _n left null because the policy mixes full-pixel and sub-pixel limits. UK and EU pages list the same Class 1 limits in more detail: 1 bright full pixel; 3 bright sub-pixels tolerated (source: https://aoc.com/uk/warranty-information).
- From the policy
- “LED panel pixel defect exceeding the ISO 9241 - 307 Class 1 specifications. Class 1 panels permit any or all of the following and is only considered a defect if it exceeds these qualifications: 1 full bright ("stuck on white") pixel; 1 full dark ("stuck off") pixel.”
Source: Warranty Information (AOC USA) - General Warranty Statement, read 2026-11-16 |
| AOC AGON | per ISO 9241-307 Class 1 (general statement on the same US page lists 1 full bright pixel plus sub-pixel allowances)Counted in pixels and sub-pixels | per ISO 9241-307 Class 1 (general statement on the same US page lists 1 full dark pixel plus sub-pixel allowances) | No | 4 years (Re-Spawned Limited Warranty) |
- Counted in
- mixed
- ISO class cited
- ISO 9241-307 Class I
- Sub-pixel or cluster rule
- Same Class 1 sub-pixel allowances as general statement: 2 single or double bright or dark sub-pixels; 3 to 5 stuck on/off sub-pixels.
- Lines covered
- AGON (gaming)
- Notes
- No AGON-specific pixel threshold; AGON gets a longer term (4 years) and new-unit replacement ("EPI will replace the entire Product at no charge with a new monitor (of the same type)"). The Re-Spawned warranty references Class 1 without listing counts; counts come from the general statement on the same page. Also a one-time Accidental Damage Exchange (1 year, refurbished replacement). Covers US/Canada purchases; excludes purchases before Jan 1, 2019.
- From the policy
- “Four (4) years from the date of purchase from EPI by You ... "Defect" means (i) for the LED panel in the Product, any pixel defect exceeding the ISO 9241 - 307 Class 1 specifications”
Source: Re-Spawned Limited Warranty for AOC G-Series Monitors and AOC AGON Monitors, read 2026-11-16 |
| Acer Predator, Nitro, standard (US) | No US policy published | | | 3 years (Monitors, Consumer & Commercial: Three-year limited warranty) |
- Lines covered
- Predator, Nitro, Standard (US pixel policy)
- Notes
- No US Acer pixel policy page found: acer.com/us-en/support/warranty/dead-pixel, /pixel-policy and /support/warranty return 404; old acer.com/ac/en/US/content/standard-warranty returns 410. The US limited warranty page gives only lengths (and notes 3-year OLED burn-in coverage). No Predator- or Nitro-specific monitor pixel policy found in any region.
- From the policy
- “Monitors | Consumer & Commercial | Three-year limited warranty”
Source: Limited Warranty | Acer United States, read 2026-11-16 |
| HP Standard, incl. OMEN | 2 bright sub-pixel defects maximum; 0 full pixel defects allowedCounted in pixels and sub-pixels | 5 dark sub-pixel defects maximum; 0 full pixel defects allowed | No | Not stated |
- Counted in
- mixed
- Sub-pixel or cluster rule
- Total combined bright and dark sub-pixel defects: 5 maximum. Full pixel defects: 0 allowed. No contamination allowed. No adjacency/distance rule stated.
- Zero defect terms
- No zero-bright-dot promise for standard monitors; zero tolerance applies only to full pixel defects (defined as a combination of one red, one green and one blue sub-pixel), not to sub-pixel defects.
- Lines covered
- Standard (HP monitors and All-in-One PCs manufactured May 2009 or later; includes OMEN and other non-Z lines)
- Notes
- The policy states it applies "during the HP limited warranty period". Monitors manufactured before May 2009 follow an older table (3 bright sub-pixel max, 5 dark sub-pixel max, 5 combined, 0 full pixel). The policy page does not name OMEN; no separate OMEN monitor pixel policy was found on support.hp.com, so OMEN appears to fall under this general policy (not stated explicitly by HP). The page notes it does not pertain to notebook displays. Warranty length is not on the policy page and is set per model; the HP US Store page for the Series 5 Pro 527pq shows "3-Year Standard Warranty", but no line-wide figure was found, so left null.
- From the policy
- “POLICY FOR HP MONITORS AND ALL-IN-ONE PCS MANUFACTURED IN MAY 2009 OR LATER ... Bright sub-pixel defects 2 maximum; Dark sub-pixel defects 5 maximum; Total combined bright and dark sub-pixel defects 5 maximum; Full Pixel Defects 0 allowed.”
Source: HP and Compaq LCD monitors, HP TouchSmart PCs, and HP All-in-One PCs - HP Pixel Policy, read 2026-11-16 |
| HP Z series and Series 7 Pro | 0 bright sub-pixel defects (Zero Bright Dots guarantee); 0 full pixel defects allowedCounted in pixels and sub-pixels | 4 dark sub-pixel defects maximum; 0 full pixel defects allowed | Yes, bright only | 3 years (HP US Store "3-Year Standard Warranty" for Series 7 Pro 727pk; no line-wide statement and no US Z-series page found) |
- Counted in
- mixed
- Sub-pixel or cluster rule
- Total combined bright and dark sub-pixel defects: 4 maximum. Full pixel defects: 0 allowed. No adjacency/distance rule stated.
- Zero defect terms
- Zero bright sub-pixel defects ("Zero Bright Dots") for all HP Z series and HP Series 7 Pro displays, during the HP limited warranty period (the page says its policies apply during that period). Bright only; up to 4 dark sub-pixel defects (4 combined) tolerated.
- Lines covered
- Z series (incl. Z DreamColor) and HP Series 7 Pro (Performance displays)
- Notes
- DreamColor is not named on the page; current/recent DreamColor monitors are Z-branded, so they fall under the Z series rule by name. Older non-Z DreamColor models are not addressed. "Most HP Performance displays" is not defined beyond Z series and Series 7 Pro. Warranty: the HP US Store product page for the HP Series 7 Pro 27-inch 4K Thunderbolt 4 Monitor 727pk (https://www.hp.com/us-en/shop/pdp/hp-series-7-pro-27-inch-4k-thunderbolt-4-monitor-727pk) lists "3-Year Standard Warranty"; US Z-series store/spec pages redirected or returned 404, and HP non-US pages and datasheets (e.g. Z27k G3, Z34c G3) state a 3-year limited warranty. Treat as model-level, not a line-wide HP statement.
- From the policy
- “For most HP Performance displays, HP guarantees Zero Bright Dots. This policy applies to all HP Z series and HP Series 7 Pro displays. ... Bright sub-pixel defects 0 maximum; Dark sub-pixel defects 4 maximum.”
Source: HP and Compaq LCD monitors, HP TouchSmart PCs, and HP All-in-One PCs - HP Pixel Policy, read 2026-11-16 |
| MSI Gaming (MEG, MPG, MAG, G) | Qualifies when bright dots > 3 (up to 3 tolerated), with bright dot gap condition L >= 15mmCounted in dots (not defined) | Qualifies when dark dots > 5 (up to 5 tolerated) | No | 3 years (MEG, MPG, OLED; MAG/G series 3 years if purchased on/after 01/01/2024, 2 years before) |
- Counted in
- dot (not defined)
- Sub-pixel or cluster rule
- "Bright dot gap < L >=15mm" (distance condition on bright dots, wording ambiguous as published). No total-combined limit stated.
- Zero defect terms
- Policy explicitly states MSI monitors do not have a 0 pixel defect warranty.
- Lines covered
- Gaming (MEG, MPG, MAG, G series, OLED)
- Notes
- Same DOT policy text appears on every monitor tab of the page (Gaming, Content Creation, Business Productivity, Portable). Dots are defined only by appearance: bright under a BLACK pattern, dark under pure red, green or blue pattern; the page does not say whether a dot is a pixel or sub-pixel. bright_allowed_n of 3 ignores the separate, ambiguously worded 15mm gap condition, which may make fewer dots qualify when close together. Gaming tab also lists Optix MPG (3 years) and Optix MAG/Optix G/Oculux. Page says regional differences may apply. A region-specific MSI Dot Killer Promise Program (Indonesia) was seen in search but is not a US policy and was not verified.
- From the policy
- “MSI Monitor do not have 0 pixel defect warranty DOT Policy : Bright Dot > 3 Dots, Bright dot gap < L >=15mm Dark Dot > 5 Dots”
Source: MSI USA - Warranty (Monitors > Gaming Monitor tab), read 2026-11-16 |
| MSI Business and Creator | Qualifies when bright dots > 3 (up to 3 tolerated), with bright dot gap condition L >= 15mmCounted in dots (not defined) | Qualifies when dark dots > 5 (up to 5 tolerated) | No | 36 months (Modern MD, Pro MP, Creator, Summit, Prestige); 24 months (portable Optix MAG) |
- Counted in
- dot (not defined)
- Sub-pixel or cluster rule
- "Bright dot gap < L >=15mm" (distance condition on bright dots, wording ambiguous as published). No total-combined limit stated.
- Zero defect terms
- Policy explicitly states MSI monitors do not have a 0 pixel defect warranty.
- Lines covered
- Standard (Business Productivity: Modern MD, Pro MP; Content Creation: Creator, Summit, Prestige; Portable)
- Notes
- Identical DOT policy to the gaming row; split only because warranty lengths differ by tab. On these tabs the no-0-pixel sentence ends with a period ("MSI Monitor do not have 0 pixel defect warranty."); on the Gaming tab it runs into "DOT Policy :" without a period. bright_allowed_n of 3 ignores the ambiguous 15mm gap condition. Regional differences may apply per the page.
- From the policy
- “MSI Monitor do not have 0 pixel defect warranty. DOT Policy: Bright Dot > 3 Dots, Bright dot gap < L >=15mm Dark Dot > 5 Dots”
Source: MSI USA - Warranty (Monitors > Business Productivity / Content Creation / Portable Monitor tabs), read 2026-11-16 |
| BenQ PD, SW and PV (Zero Bright Dot models) | 0 (Zero Bright Dot guarantee; even one bright pixel qualifies for free exchange)Counted in sub-pixels | Not stated | Yes, bright only | 3 years |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- ZBD criteria are stated for bright sub-pixels (a red, blue or green sub-pixel always lit on a black background). Usage conditions: ambient illuminance more than 200 lux, viewing distance more than 35 cm. No dark-pixel tolerance stated for ZBD models in the US policy.
- Zero defect terms
- Bright sub-pixels only, PV/SW/PD models except PD2500Q/PD2710QC/PD3200U/SW271. Contradictory duration on the same page: the text says a free monitor exchange is guaranteed "during the Limited Warranty period" (3 years), but the criteria table lists "Warranty Period: 30 days from date of purchase" for Bright Sub-Pixel Defect.
- Lines covered
- PD / SW / PV (Zero Bright Dot models; excludes PD2500Q, PD2710QC, PD3200U, SW271)
- Notes
- Internal contradiction on ZBD duration: "during the Limited Warranty period" in the text vs "30 days from date of purchase" in the criteria table; both recorded. The headline sentence says "one bright pixel" but the criteria table is for bright sub-pixels. The resolution table explicitly excludes ZBD models, so the US policy is silent on dark-pixel tolerance for PD/SW/PV. Same text appears in the US PDF https://www.benq.com/content/dam/b2c/en-us/support/warranty/benq-dead-pixel-policy-v2-20180316.pdf (v2, 2018; not re-opened in this audit). EU differs (not re-verified in this audit): the EU EN policy PDF (https://www.benq.eu/content/dam/b2c/en-eu/support/warranty/monitors/benq-lcd-monitor-dead-pixel-policy-EN.pdf) reportedly lists specific ZBD models, a 6-month ZBD period, and excludes dark sub-pixels and partially lit sub-pixels from ZBD.
- From the policy
- “Even if only one bright pixel is found, a free monitor exchange is guaranteed during the Limited Warranty period. ... Applicable Models: PV/SW/PD models (Not Include: PD2500Q/PD2710QC/PD3200U/SW271) ... Warranty Period: 30 days from date of purchase”
Source: BenQ America Corp. End User Limited Warranty - LCD Monitors (PD2706U warranty page), read 2026-11-16 |
| BenQ Standard, incl. MOBIUZ | per resolution table: 3 below FHD; 2 at FHD, QHD and UHD (acceptable bright sub-pixels)Counted in sub-pixels | per resolution table: 3 below FHD; 5 at FHD, QHD and UHD (acceptable dark sub-pixels) | No | 3 years |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Total allowable sub-pixel defects: 5 at every resolution. No adjacency/distance or center-zone rule in the US policy.
- Lines covered
- Standard (all non-ZBD monitors, incl. MOBIUZ EX, GW, etc.)
- Notes
- "BenQ's manufacturer warranty covers any defects that exceed the defect specifications described in this document." US warranty: three years from purchase by the original retail purchaser, parts and labor, no advance replacement; DOA must be reported within 30 days. Page notes the specification "may vary from different regions". Same warranty text is served on PD, SW and EX model pages. EU policy differs (not re-verified in this audit): repair eligibility at no less than 5 defective subpixels across the screen, or at least 1 defective subpixel in the central zone, photos required (EU EN PDF linked in the PD/SW row notes).
- From the policy
- “The specifications for the number of defects that are deemed to be acceptable for each size of LCD panel (exclusive of models applicable to ZBD guarantees) are: ... Full HD (FHD) 1920x1080 (1080p): Bright sub-pixel 2, Dark sub-pixel 5, Total Allowable Sub-pixel 5.”
Source: BenQ America Corp. End User Limited Warranty - LCD Monitors (EX2710Q warranty page), read 2026-11-16 |
| Lenovo All monitors, incl. ThinkVision and Legion | 0 full bright pixels (pixel defects not permitted); up to 2 bright sub-pixels, max 5 defective sub-pixels totalCounted in pixels and sub-pixels | 0 full dark pixels (pixel defects not permitted); up to 5 dark sub-pixels, max 5 defective sub-pixels total | No | 3 years (Lenovo PSREF base warranty for sampled models, e.g. Legion Y27-30, ThinkVision P27h-30 and T27i-30: 3-year courier or carry-in service); may vary by model/region |
- Counted in
- mixed
- ISO class cited
- ISO 9241 Class I
- Sub-pixel or cluster rule
- Pixel and adjacent sub-pixel defects are not permitted. Table (13.3in to 43.4in): Pixel Defect 0, Bright Sub Pixels 2, Dark Sub Pixels 5, Total Sub Pixels 5 on every row. Service applies if defective sub-pixel counts exceed the table during the warranty period.
- Zero defect terms
- No zero-defect promise for the general policy: full-pixel defects are not permitted, but up to 2 bright and 5 dark sub-pixel defects (5 total) are tolerated.
- Lines covered
- Standard (all Lenovo monitors incl. ThinkVision and Legion, except ThinkVision P/T Series Gen-40)
- Notes
- Policy explicitly applies to Consumer and Commercial Lenovo Monitors and All-in-One Desktop Systems. Legion has no separate published pixel policy, so it falls under this general policy. The table's "ISO9241 Class 1" column is "Y" for every row except 14.0in 1366x768 ("N"); the policy text says sub-pixel defects "in most products" meet Class 1. Lenovo defines a Bright Pixel as all three RGB sub-pixels lit and a Bright Sub Pixel as one lit sub-pixel. The policy says to "contact Lenovo or your service provider for assistance" rather than promising replacement. _n left null because the policy has separate pixel and sub-pixel limits. Warranty length is from PSREF spec pages for sampled models, not from the pixel policy page (not re-verified in this audit).
- From the policy
- “All Lenovo Monitors and All-in-One Desktop Systems (Commercial and Consumer) will exceed ISO 9241 Class 1 and Class 2 requirements in that Pixel and adjacent Sub Pixel Defects are not permitted. Sub pixel defects in most products meet ISO9241 Class 1 requirements as shown below in the table.”
Source: What if defective pixel is found on your monitor - Policy and Standard, Lenovo Monitors and All-in-One Desktop - Lenovo Support US, read 2026-11-16 |
| Lenovo ThinkVision P and T Gen-40 | 1 bright pixel during the warranty period qualifies for assistance (note does not say pixel or sub-pixel; Lenovo defines Bright Pixel as all three sub-pixels lit); sub-pixel limits otherwise per general tableCounted in pixels and sub-pixels | per general Lenovo table: 0 full dark pixels; up to 5 dark sub-pixels, max 5 sub-pixel defects total | Not stated | Not stated |
- Counted in
- mixed
- ISO class cited
- ISO 9241 Class I
- Sub-pixel or cluster rule
- General table otherwise applies: pixel and adjacent sub-pixel defects not permitted; Bright Sub Pixels 2, Dark Sub Pixels 5, Total Sub Pixels 5.
- Zero defect terms
- Note covers bright pixels only, for the whole warranty period, ThinkVision P and T Series Gen-40 only, but it says "contact Lenovo or your service provider for assistance" rather than explicitly promising replacement or repair, and the general table already allows 0 full-pixel defects for all models, so what the note adds is unclear.
- Lines covered
- ThinkVision P and T Series Gen-40
- Notes
- The note does not say whether "1 bright pixel" means a full pixel or a sub-pixel. Under Lenovo's own definitions a Bright Pixel is all three sub-pixels lit, which the general table already allows 0 of; if it means a bright sub-pixel, it would lower the Gen-40 bright sub-pixel tolerance from 2 to 0. Warranty length for Gen-40 models not confirmed.
- From the policy
- “Note: For Lenovo ThinkVision P and T Series Gen-40 monitors, if there is 1 bright pixel detected during the warranty period, then contact Lenovo or your service provider for assistance.”
Source: What if defective pixel is found on your monitor - Policy and Standard, Lenovo Monitors and All-in-One Desktop - Lenovo Support US, read 2026-11-16 |
| ViewSonic All monitors (US) | per resolution: up to 2 bright below 3840x2160; up to 5 bright at 3840x2160 or higherCounted in pixels | per resolution: up to 2 dark below 3840x2160; up to 5 dark at 3840x2160 or higher | No | 3 years (parts, labor and LCD backlight) |
- Counted in
- pixel
- Sub-pixel or cluster rule
- Total improperly operating pixels: 3 below 3840x2160; 8 at 3840x2160 or higher.
- Lines covered
- Standard (all ViewSonic monitors, US)
- Notes
- Called the "LCD Pixel Performance Guarantee". The US page does not mention VP or ColorPro, so in the US ColorPro appears to fall under this policy. EU differs: the ViewSonic Europe pixel policy PDF lists bright dot (white pixel) N<=2 / dark dot (black pixel) N<=4 / combined N<=5 for 2560x1440 or smaller and 5/5/8 for 3840x2160 or larger, and offers zero defective pixels for VP and VG series. "B" grade refurbished units follow the same pixel policy as new; "C" grade may exceed it.
- From the policy
- “Panels with resolution smaller than 3840x2160: Three (3) improperly operating pixels and no more than two (2) bright or two (2) dark pixels. Panels with resolution 3840x2160 or higher: Eight (8) improperly operating pixels and no more than five (5) bright or five (5) dark pixels.”
Source: Limited Warranties, read 2026-11-16 |
| Gigabyte AORUS (LCD under 40 in) | 0 within first 12 months; 3 tolerated in months 13-36 (4th bright dot qualifies)Counted in pixels | 5 tolerated (6th dark dot qualifies) | Yes, bright only | 3 years (LCD under 40 inches); 1 year for 40 inches or over and OLED |
- Counted in
- pixel
- Sub-pixel or cluster rule
- Bright dots defined as "non-performing pixels appearing as a red, green, blue, yellow, cyan, magenta, or white dots on a dark or black background"; dark dots as dark non-performing pixels on a bright or white background. Inspection at 35cm or more, ambient illumination greater than 200 Lux. No cluster/distance rule stated.
- Zero defect terms
- Bright dots only, first 12 months after purchase, AORUS series small/medium LCD (under 40 inches).
- Lines covered
- Aorus (LCD under 40 inches)
- Notes
- Page also says "It's guaranteed there will be no bright dots on the whole panel area", but the table limits zero bright dots to the first 12 months (0 within 12 months, <=3 within 13-36 months; dark <=5 throughout). bright_allowed_n reflects the 12-month guarantee period. The dot policy applies only to small and medium LCD under 40 inches; no pixel policy stated for OLED or 40-inch-plus models. Page states regional differences apply; DOA/RMA policy varies by country. Page blocks automated fetch (HTTP 403) and was read in a browser.
- From the policy
- “New products are guaranteed to be zero bright dot for 12 months. During 13~36 months after purchase, bright dots must be more than 3 dots (which refers to the 4th dot)”
Source: Warranty - GIGABYTE United States, read 2026-11-16 |
| Gigabyte GIGABYTE series (LCD under 40 in) | 3 tolerated (4th bright dot qualifies), months 0-36Counted in pixels | 5 tolerated (6th dark dot qualifies) | No | 3 years (LCD under 40 inches); 1 year for 40 inches or over and OLED |
- Counted in
- pixel
- Sub-pixel or cluster rule
- Bright dots defined as "non-performing pixels appearing as a red, green, blue, yellow, cyan, magenta, or white dots on a dark or black background". Inspection at 35cm or more, ambient illumination greater than 200 Lux. No cluster/distance rule stated.
- Lines covered
- Standard (GIGABYTE series, LCD under 40 inches)
- Notes
- Dot policy applies only to small/medium LCD under 40 inches; nothing stated for OLED or 40-inch-plus. Regional differences apply per the page.
- From the policy
- “Bright dot warranty conditions: Bright dots must be more than 3 dots (which refers to the 4th dot). Dark dot warranty conditions: Dark dots must be more than 5 dots (which refers to the 6th dot)”
Source: Warranty - GIGABYTE United States, read 2026-11-16 |
| Corsair Xeneon | 0 (1 or more bright pixels qualifies for exchange; a bright pixel is defined as a bright white, red, blue or green dot always on against black)Counted in pixels and sub-pixels | up to 5 dark subpixels (6 or more dark subpixels qualifies for exchange; policy notes 3 subpixels = 1 pixel) | Yes, bright only | 3 years |
- Counted in
- mixed
- Sub-pixel or cluster rule
- Policy states three subpixels count as one pixel. No cluster, adjacency or zone rules stated.
- Zero defect terms
- Bright pixels only: exchange for 1 or more bright pixels during the hardware warranty period (3 years for new Xeneon monitors; certified refurbished monitors have a 90-day hardware warranty). Dark defects need 6 or more dark subpixels. Scope: the help-center version covers monitors bought 'in new condition from Corsair.com or an authorized Corsair reseller'; the explorer page version says 'from our Webstore'. Corsair's warranty guide calls this a 'Zero Dead Pixel Policy', but the published chart applies zero tolerance only to bright pixels.
- Lines covered
- Xeneon
- Notes
- Called the 'Panel Quality Guaranty'. The help-center version (https://help.corsair.com/hc/en-us/articles/4406316660621, 'XENEON Monitor: Corsair monitor dead pixel policy') has the same chart but wider scope: 'If you purchase a Corsair monitor in new condition from Corsair.com or an authorized Corsair reseller...'. Warranty length from the official Corsair 'Monitor Warranty Guide & Zero Dead Pixel Policy' PDF (https://assets.corsair.com/image/upload/corsairmedia/sys_master/productcontent/49_002500_AA_WW_Monitor_Warranty.pdf): 'CORSAIR XENEON MONITORS come with a 3-year hardware warranty for the original purchaser, starting from the day of purchase from an authorized CORSAIR reseller.' Certified refurbished monitors get 90 days. Thresholds use different units (bright in pixels, dark in subpixels), so dark_allowed_n is null; bright_allowed_n 0 is kept because any bright pixel qualifies regardless of unit.
- From the policy
- “If you purchase a Corsair monitor from our Webstore and find a certain amount of bright pixels or dark subpixels, we will exchange your monitor during the hardware warranty period. NOTE: 3 subpixels is equal to 1 pixel. [Chart: Xeneon monitors | 1 or more | 6 or more]”
Source: Corsair monitor dead pixel policy | CORSAIR, read 2026-11-16 |
| Philips Evnia QD-OLEDWorldwide terms | 0 (acceptable level 0 for 1 lit subpixel, 2 adjacent lit subpixels, 3 adjacent lit subpixels (one white pixel), and total bright dot defects of all types)Counted in pixels and sub-pixels | per type: 1 dark subpixel 5 or fewer; 2 adjacent dark subpixels 2 or fewer; 3 adjacent dark subpixels 1 or fewer; total black dot defects 5 or fewer | Yes, bright only | Not stated |
- Counted in
- mixed
- Sub-pixel or cluster rule
- 1 or 2 adjacent sub pixel defects = 1 dot defect. Distance between two bright dot defects: 0 (as printed). Distance between two black dot defects: 5mm. Total bright or black dot defects of all types: 5 or fewer.
- Zero defect terms
- Bright dots only: acceptable level for every bright dot type is 0, so any lit subpixel exceeds tolerance and qualifies for repair/replacement during the warranty period. Dark dots have thresholds. Applies to the QD-OLED Evnia manuals checked; Evnia LCD models use the standard table.
- Lines covered
- Evnia (QD-OLED models, e.g. 27M2N6500P, 27M2N6501L, 27M2N6591L)
- Notes
- Same table found in Evnia QD-OLED manuals 27M2N6501L (https://www.documents.philips.com/assets/20251030/603caf403e9a404faa9ab386007c0c9e.pdf) and 27M2N6591L (https://www.documents.philips.com/assets/20260525/483cfd8c4e334eb49de2b455003a9c20.pdf). Policy text states 'This policy is valid worldwide.' No ISO class cited in these manuals. Manual defers warranty length to the regional 'Warranty Statement in the Important information manual'; a US warranty length could not be verified on an official page, so warranty_length left null. Limits are set per single subpixel, adjacent subpixels, whole white pixel and dot defect, so threshold_unit is mixed; bright_allowed_n 0 kept because every bright type is 0.
- From the policy
- “To qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub-pixel defects exceeding the tolerances listed in the following tables. [Table: Total bright dot defects of all types - ACCEPTABLE LEVEL 0]”
Source: Philips 27M2N6500P User manual, section 12.1 Philips' Panel Monitors Pixel Defect Policy, read 2026-11-16 |
| Philips Standard and Evnia LCDWorldwide terms | per type: 1 lit subpixel 2; 2 adjacent lit subpixels 1; 3 adjacent lit subpixels (one white pixel) 0; total bright dot defects of all types 2Counted in pixels and sub-pixels | per type: 1 dark subpixel 3 or fewer; 2 adjacent dark subpixels 2 or fewer; 3 adjacent dark subpixels 0; total black dot defects 3 or fewer | No | Not stated |
- Counted in
- mixed
- Sub-pixel or cluster rule
- 1 or 2 adjacent sub pixel defects = 1 dot defect. Distance between two bright dot defects >15mm; distance between two black dot defects >15mm. Total bright or black dot defects of all types: 5 or fewer. A red or bright blue dot must be more than 50 percent brighter than neighboring dots; a bright green dot 30 percent.
- Zero defect terms
- No zero-defect promise; up to 2 single lit subpixels tolerated. A fully white pixel (3 adjacent lit subpixels) has acceptable level 0.
- Lines covered
- Standard (e.g. 273S1) and Evnia LCD models (e.g. 25M2N3200XI, 27M4P5501X)
- Notes
- Identical table in the Philips 273S1 (S Line, standard) manual (https://www.documents.philips.com/assets/20240521/1a4c4483007d4a98817eb17700c5b9aa.pdf) and the Evnia 27M4P5501X manual (https://www.documents.philips.com/assets/20260616/76dfd2e61f394eb4b8efb46b005da057.pdf). The policy states 'This policy is valid worldwide.' Evnia LCD models follow the standard policy; Evnia QD-OLED models have zero bright tolerance (separate row). The current manuals checked cite no ISO class. Warranty length deferred to the regional Important information manual; not verified on an official US page.
- From the policy
- “To qualify for repair or replacement under warranty, the number of pixel defects on a TFT Monitor panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub-pixels on a monitor may be defective.”
Source: Philips 25M2N3200XI User manual, section 9.1 Philips' Flat Panel Monitors Pixel Defect Policy, read 2026-11-16 |
| Eizo ColorEdge (listed models) | 0 (zero bright sub-pixels allowed for six months after purchase)Counted in sub-pixels | Not stated | Yes, bright only | 5 years or 30,000 hours (incl. LCD panel module) |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Counts sub-pixels: a bright sub-pixel is a red, blue, or green pixel always lit on a black background. Excludes partially lit sub-pixels, foreign substances, and dark sub-pixels. Inspection: ambient illuminance more than 500 lux, viewing distance more than 14 inch (35 cm).
- Zero defect terms
- Bright (fully lit) sub-pixels only, zero allowed, for six months after purchase, on listed models purchased on or after September 1, 2015. Dark sub-pixels are explicitly excluded; no dark threshold published. After six months no pixel threshold is published.
- Lines covered
- ColorEdge (bright pixel warranty models: CG3146, CG3145, CG319X-4K, CG248-4K, CG279X, CG277, CG2730, CG247X, CG247, CG2420, CX271, CX241, CS2740, CS2731, CS2730, CS270, CS2420, CS240, CS230)
- Notes
- Other ColorEdge models (CG276, CG246, CX270, CX240) have 5 years or 30,000 hours without the bright pixel warranty; older wide/CE/SX models have 5 years or 30,000 hours with 3 years for the LCD panel module. CG3146/CG3145 are also listed in a separate '5 years or 10,000 hours (Incl. LCD panel module)' row; the page does not explain which applies. The General Provisions exclude 'defects in pixels including burnt pixels' caused by deterioration of expendable parts such as the LCD panel. Original announcement: https://www.eizo.com/news/eizo-guarantees-zero-bright-pixels-for-six-months/ (Sept 2015).
- From the policy
- “EIZO's policy covers visible, bright (fully-lit) sub-pixels as detailed in the following table. Allowable number of bright sub-pixel Zero ... Warranty period Six months after purchase”
Source: ColorEdge Warranty & Recycling Information | EIZO, read 2026-11-16 |
| Eizo FlexScan (listed models) | 0 (zero bright sub-pixels allowed for six months after purchase)Counted in sub-pixels | Not stated | Yes, bright only | 5 years or 30,000 hours (incl. LCD panel module) |
- Counted in
- sub-pixel
- Sub-pixel or cluster rule
- Counts sub-pixels: a bright sub-pixel is a red, blue, or green pixel always lit on a black background. Excludes partially lit sub-pixels, foreign substances, and dark sub-pixels. Inspection: ambient illuminance more than 500 lux, viewing distance more than 14 inch (35 cm).
- Zero defect terms
- Bright (fully lit) sub-pixels only, zero allowed, for six months after purchase, on listed EV models purchased on or after September 1, 2015. Dark sub-pixels excluded; no dark threshold published.
- Lines covered
- FlexScan (bright pixel warranty EV models: EV3895, EV2795, EV2495, EV2760, EV2460, EV2336W, EV2436W, EV2450, EV2455, EV2456, EV2736W, EV2750, EV2785, EV2730Q, EV3237, EV3285)
- Notes
- Other FlexScan models (EV2216W/EV2316W/EV2416W, S1503-S2133 S series) have 5 years or 30,000 hours without the bright pixel warranty; many older models 5 years or 30,000 hours with 3 years for LCD panel module; touch models and all FlexScan monitors not listed have 3 years (incl. LCD panel module). The General Provisions exclude 'defects in pixels including burnt pixels' caused by deterioration of expendable parts such as the LCD panel.
- From the policy
- “Allowable number of bright sub-pixel Zero Applicable monitors The above-mentioned models purchased on or after September 1, 2015 Warranty period Six months after purchase”
Source: FlexScan Warranty & Recycling Information | EIZO, read 2026-11-16 |
| Apple Studio Display, Pro Display XDR | No US policy published | | | 1 year (Apple Limited Warranty) |
- Lines covered
- Studio Display, Pro Display XDR
- Notes
- Apple publishes no numeric pixel defect threshold for its displays. The pixel anomalies article gives no counts and does not name Studio Display or Pro Display XDR; it suggests having a device examined by Apple or an authorized provider. Warranty length from https://support.apple.com/displays/repair ('Apple Service and Repair for Apple Display - Apple Support'): the Apple Limited Warranty covers the device 'against manufacturing issues for one year from the date you bought them.' Status not_found refers to pixel thresholds.
- From the policy
- “Apple strives to use the highest quality LCD panels in its products, however pixel anomalies can occur in a small percentage of panels.”
Source: About LCD display pixel anomalies for Apple products released in 2010 and later, read 2026-11-16 |